The OBDII trouble code of P0335 is known as a “hard” code, an interpretation severely detrimental to the procedure of your Accord engine. Much more specifically the DTC P0335 to represent a absence of signal from the crankshaft place sensor. The crankshaft position sensor in her Honda Accord notifies your ECU the the crankshaft speed and current location.

You are watching: 1996 honda accord crankshaft position sensor location

Without this data, the engine will either no run or run an extremely poorly. Typical symptoms are challenge starting or the engine might shut off randomly, producing a an extremely dangerous case for not just the driver but the passengers together well.

Possible causes of OBDII examine engine light P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be mirroring you just how to service and replace your crankshaft position sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The component number because that this component is 37840-P0A-A01 because that the crankshaft place sensor in your Honda Accord. The can also be found under the part number of 37840-PAA-A01.


*

This How To adjust a Honda Accord Crankshaft place Sensor DIY overview assumes girlfriend have currently removed your driver side engine mount and also supported your engine with a jack. Please check our how To readjust a Honda Accord time Belt overview for an ext details.

Before you start our DIY overview on how To adjust a Honda Accord Crankshaft position Sensor, you must disconnect the negative terminal on your battery. As proclaimed previously, this overview assumes you can raise and also lower her F23 already, i m sorry is mandatory when an altering your time belt.

*

Unplug your four pin connector the runs to your crankshaft place sensor in your Honda Accord. Here’s what her pigtail look at like an installed to your F23A1. It’s secured by a 10mm bolt that runs with the earlier of her VTEC SOHC engine.

*

This exploit to your crankshaft position sensor runs through your reduced timing plate, which have to be gotten rid of to change a Honda Accord Crankshaft position Sensor. In bespeak to do this, girlfriend must lower your engine if still linked to your chassis, and also remove the crankshaft pulley-block or harmonic balancer.

This may be daunting if you are working ~ above the ground v hand tools and also don’t have a air compressor through the right air tools. Use a Honda crankshaft wrench, Moroso component number 61805 to correctly loosen her crankshaft bolt there is no air tools.

*

With the bolt removed, girlfriend should have the ability to wiggle off your crankshaft pulley and set it safely come the side. Make sure eliminate your woodruff key and save that as safe as your pulley.

*

Now you have the right to remove all the 10mm bolts that organize your reduced timing sheathe in place. Remove these one-of-a-kind bolts and also then do your way to the valve cover, friend will require to ago off the valve sheathe bolts that run with to the cylinder head.

Loosen every the valve sheathe bolts, but do no remove and also gently loosen your valve cover. Lift the valve cover to enable enough room for your upper SOHC VTEC timing cover come come off your engine. There room 2 10mm bolts that run through the top cover come the cylinder head, remove these to loosen your upper timing cover.

*

Now slide turn off your reduced timing cover and pull under to relax from your side engine mount. You have to now see your timing belt assembly and your F23A1 balance shafts and also belts. The crankshaft place sensor in your Honda Accord is located behind the crank cause plate.

*

You deserve to take one of two paths to removing your crankshaft place sensor and also replacing it. You deserve to loosen your timing belt tensioner bolt, the longated bolt situated in the center of your tensioner arm. This should allow enough slack as to gently ago off your lower crank wheel plate and also undo the 10mm bolt that holds the crankshaft position sensor in place.

*

If this is no an choice for you, examine out our exactly how To change a Honda Accord time Belt overview on just how to properly time and also remove your F23A1 belts to service your crankshaft place sensor.

There are numerous timing marks for your balance obelisk that we recommend you line as much as TDC before removing your balance column belts.

See more: How Long Does Wheat Germ Last, Do You Need To Refrigerate Wheat Germ

*

Before removing your balance obelisk belts to reach your crankshaft position sensor, you will require to double check time marks to ensure your F23a1 is at TDC. Again for an ext details inspect our how To DIY guide on changing the Honda Accord time belt.

*

Once you have actually replaced your Honda Accord crankshaft place sensor, you can use a scan device to effectively clear her OBDII inspect engine code of P0335. Hope we’ve helped you learn how To readjust a Honda Accord Crankshaft place Sensor, if girlfriend have any kind of questions please leave united state a comment below!